当前位置:首页-常见问题解答>>激光全息防伪标签的特点有哪些?

激光全息防伪标签的特点有哪些?

来源:http://www.shengfengyinshua.com/ 日期:2021-01-31 发布人:shengfeng 一、标识外观图案观察:
1、 Logo appearance pattern observation:
激光防伪标识图案观察,须手持激光标识于点光源下观看。如阳光、白炽灯光下,会看到明亮、清晰的图案(如阴天或荧光光源下会呈现出不清晰的图案),如果点光源下一开始看不清图案,则需转、移动激光标识角度,直到看清为止。
To observe the laser anti-counterfeiting logo pattern, it is necessary to hold the laser logo under the point light source. For example, bright and clear patterns can be seen under sunlight and incandescent light (for example, unclear patterns can be seen under cloudy day or fluorescent light). If the pattern cannot be seen clearly at first under the point light source, it is necessary to turn and move the laser marking angle until it is clear.
二、激光全息防伪的粘贴:
2、 Laser holographic anti-counterfeiting paste:
A、激光全息防伪标识粘贴在表面光滑、平整、清洁的防粘底纸上(特殊产品需要采用专用的胶水制作,客户在下订单前沟通清楚标识被粘物)。
A. The laser holographic anti-counterfeiting logo is pasted on the anti sticking backing paper with smooth, flat and clean surface (special products need to be made with special glue, and the customer should communicate clearly to identify the stuck object before placing the order).
B、从防粘底纸上提取防伪标识时,应把防粘底纸向背面沿待取防伪标识的边缘直线折叠一部分,使防伪标识自动从防粘纸上翘起一部分。
B. When the anti-counterfeiting label is extracted from the anti-counterfeiting backing paper, the anti-counterfeiting backing paper should be folded to the back along the edge of the anti-counterfeiting label to be taken, so that the anti-counterfeiting label will automatically tilt up from the anti-counterfeiting label.
激光标签制作厂家
C、从防粘纸上提取翘起的标识时,手要清洁干净,不能带有灰尘、油污、水渍等,手与防伪标识的底层涂胶面接触不宜太大,且拿捏用力适中,以免损坏标识的底层粘度;提取防伪标识时,应遵循正常揭启规律,不得强行拉拽,且速度不宜太快,太快则易损伤防伪标识;严禁直接从防粘纸上抠起防伪标识。
C. When extracting the cocked logo from the anti-counterfeiting paper, the hand should be clean, without dust, oil, water stains, etc. the contact between the hand and the bottom gluing surface of the anti-counterfeiting logo should not be too big, and the holding force should be moderate, so as not to damage the bottom viscosity of the logo. When extracting the anti-counterfeiting logo, the normal opening law should be followed, and it should not be forced to pull, and the speed should not be too fast, too fast will easily damage the anti-counterfeiting It is strictly forbidden to pick up the anti-counterfeiting mark directly from the anti sticking paper.
D、粘贴防伪标识时,被贴物表面要清洁干净,禁忌灰尘、油污和水渍等;当标识贴到被贴物表面时,应用手指用力将防伪标识压平整,使防伪标识与被贴物表面充分粘合。
D. When pasting the anti-counterfeiting label, the surface of the pasted object should be clean, and dust, oil and water stains are forbidden; when the label is pasted on the surface of the pasted object, the finger should be used to press the anti-counterfeiting label flat, so as to make the anti-counterfeiting label fully adhere to the surface of the pasted object.
三、激光防伪标识的使用:
3、 Use of laser anti-counterfeiting label:
A、揭开式激光全息图案防伪标识使用:一次性揭开式激光全息图案防伪标识在揭启时,应用手指甲沿标识的边缘某部位揭起,手指捏紧被揭起部位,再用力撕揭,全息图像应残留/部分残留在被贴物表面上/标识的平整度被破坏,无法再重复使用。
A. Use of unveiling laser holographic pattern anti-counterfeiting logo: when unveiling the one-time unveiling laser holographic pattern anti-counterfeiting logo, the fingernail should be lifted along the edge of the logo, the finger should pinch the uncovered part, and then tear it hard. The holographic image should be left / partially left on the surface of the pasted object / the flatness of the logo is damaged and cannot be reused.
B、刮开式标识使用:刮开式电话电码防伪标识在刮开覆盖墨时,先试探性刮一下,再决定用力大小,切勿一开始用力过大,损伤覆盖墨下面的数码,如个别标识覆盖墨难以刮开时,可稍微加水浸润一下,半小时再刮。
B. Use of scrape open label: when scraping off the cover ink of the scrape open telephone code anti-counterfeiting label, try to scrape it first, and then determine the force. Do not use too much force at the beginning to damage the numbers under the cover ink. If it is difficult to scrape off the cover ink of individual labels, you can add a little water and then scrape it for half an hour.
C、揭开式标识使用:揭开式电话电码防伪标识揭启时,应首先确认表层图案的提示语言,再按提示从正确位置揭启。用手指甲轻轻揭起标识边缘部分,手指捏紧被揭起部位,再慢慢揭开(切勿用力过猛,以防损伤底层),底层留在被贴物上,底层/表面背面的数码应完整并易于辨认。
C. Use of unveiling signs: when unveiling the unveiling telephone code anti-counterfeiting signs, the prompt language of the surface pattern should be confirmed first, and then unveiling from the correct position according to the prompt. Gently lift the edge of the logo with fingernails, pinch the lifted part with fingers, and then slowly lift it (do not use too much force to prevent damage to the bottom layer). The bottom layer is left on the pasted object, and the number on the back of the bottom layer / surface should be complete and easy to identify.
以上就是激光标签制作厂家http://www.shengfengyinshua.com为大家介绍的内容,感谢您在百忙之中查看我公司的信息内容,如果您想要了解的更多,欢迎您来电进行咨询!
These are laser label manufacturers http://www.shengfengyinshua.com Thank you for checking our company's information in your busy schedule. If you want to know more, you are welcome to inquire!

上一篇:印刷医药标签需要进行哪些步骤?
下一篇:标签印刷制版应该注意什么?
联系我们